Service Module Rev A ECOs (main board)

List:

• U15: ​ECO Link
• U23: ​ECO Link
• ESM: ​ESM ECO

• R94,R95,R96,R92 Remove resistors.
• Add 4.7k resistor between R95 pad bottom to R92 pad upper ​Example

• R50 should be 10k-ohms for CERN IPMC (SM603)

• R52,R56,R61,R62 should be ~100-ohms (For LEDs so ~10% is fine)

• Samtec headers for FP (J40, J46) are a bit too tall. Suggest sub SAM11085-ND (ESQ-106-23-L-D)

• Remove U11 and U13.

• Replace C2, C14, and C18 with ‎565-4114-ND‎

• Install 3 pin 0.1" header for use with jumpers on J45.
• Remove R23 and R28

• install M2.5x8 screw in K1 & K2 (on the back side.)

notes:

• 220uF caps should get smaller (physically, too tall)
• Remember to populate R50 with CERN IPMC value.
• We should add a pull-down to U15 pin 1 for when we have no IPMC (added on board 1)​ECO Link
• We should add a pull-up to ETH_SW_RESET_N (Has on-board pull-up, so we are OK)
• Traces under mounting splice plate holes
• U23 has wrong DigiKey? part number ​ECO Link
• A pull up/down should be added between U24 pin 4 and U23 pin 7

Front panel board changes for Rev B

• Remove level shifter and wire direct uSD card to connector
• Change FT232RQ to FT232RL (TSSOP package)
• Wire USB_UART_EN to FT_3V3 through R2 instead of from nDTR
• Change header P/N for headers for longer pins

Service Module TODOs for RevB

• Traces under mounting splice plate holes (move to internal layers/ out of the way)
• GPIO header
• Add level shifters between ESM LED/Serial connections to Zynq to allow for ESM to work when Zynq missing/broken.
• Zynq power good signal to IPMC
• Modify BOOTMODE flipflops
• Simple jumper for turning on 12V without an IPMC.
• Consider removing series caps on TTX Tx lines (CMS_TCDS2_TTS_P/N); suggestion from Luis @ KIT
• Extra IOs between Zynq and IPMC
• Extra IOs for Zynq-
• Extra IOs for IPMC
• Re-arrange high speed links for CMs
• Connect up second ESM second SGMII to ESM eval phy and zynq ethernet port
• Compatible with XU
• adjust hole size under zynq for mounting.

Requests / comments from Cornell

• Make the I2C busses multi-master ZYNQ+IPMC? Maybe not easy/possible but worth considering
• Any changes to the UART links to make things easier / more flexible?
• Possibly alter the SM mechanics so that CM with splice plates can just slide in and out?
• Peter complains that the SD card read/write speed is very slow. Maybe it's operating in some fallback slow mode? Worth investigating.

Rev 2 SoC US+ options

CG-> Dual-Core A53 1.3Ghz, Dual-core R5 533Mhz, 103-600k logic cells EG-> Quad-Core A53 1.5Ghz, Dual-core R5 600Mhz, GPU, 103-1100k logic cells EV-> Quad-Core A53 1.5Ghz, Dual-core R5 600Mhz, GPU, Video, 192-500k logic cells |model| chip| ram|connectors|MGBTs GTH+GTR|price| |XU1 | ZU6EG,ZU15EG | 2-4GB | 3 | 12 + 4 |700 - 2k| |XU5 | ZU2EG,ZU5EV | 2-4GB | 2 | 4 + 4 | | |xu7 | ZU6EG,ZU15EG | 2-4GB | 3 | 16 + 4 |1.2k - 2k| |xu8 | ZU4CG,ZU7EV | 2-4GB | 3 | 16 + 4 | 700-1.6k |xu9 | ZU7EV | 2-4GB | 3 | 16 + 4 | 1.7k |