| Version 78 (modified by , 5 years ago) (diff) |
|---|
Service Module
Rev A
| remote access? | ID | Cirex | Location | CM? | Notes | ECOs | |
| yes/no (Dan's) | 001 | 98716 | BU (table) | K | Hard-wired 12V on, misc on, zynq bank IO on. Pulldown on zynq_en. 1k pulldown on U15 pin 1. Jumper on switch en to 3.3V. Removed R35 and R40. | 1, 2 | |
| no | 002 | 98724 | BU (Assembly Shelf) | - | for show. Test paused after zynq booted successfully. Test completed. | 1, 2 | |
| no | 003 | BU (table) | - | 1k pulldown on U15. switch fix. J28 has a connector, should be removed. | 1, 2 | ||
| no | 004 | 98719 | BU (Assembly Shelf) | - | Resistor between R95 and R92 came off before step "put in zynq." LEDs lit up incorrectly. Stopped testing. Trial 2: Numerous LEDs lit up incorrectly at the same step (6: put in zynq). Stopped again. | 1, 2 | |
| yes | 005 | 98720 | BU (in Shelf) | - | LEDs hot-wired permanently on | 1, 2 | |
| yes | 006 | 98721 | BU (in Shelf) | K+V | Test paused after zynq booted successfully. | 1, 2 | |
| - | 007 | 98723 | Amhert | - | Missing LED after all ECOs completed. Resoldered new LED. Test completed. | 1, 2 | |
| no | 008 | 98717 | CERN TIF | - | Missing LED after all ECOs completed. Resoldered new LED. Test paused after zynq booted successfully. Test completed. | 1, 2 | |
| - | 009 | 98725 | Cornell | - | Test paused after zynq booted successfully. Test completed. | 1, 2 | |
| - | 010 | 98718 | Cornell | ? | Test paused after zynq booted successfully. | 1, 2 | 19100056 |
ECO_1: Connect J5 pin-14 to 3V3_STBY through any lower 3 pins of J5 (p 2,4,6).
ECO_2: Add a 1k-Ohm resistor between the pad of R40 to GND pin of J12.
IPMC
Default IP is 192.168.1.34
CERN
| ID | Location | MAC | IP | History |
| 19100056 | BU (Assembly Shelf) | 00:50:51:FF:00:05 | 192.168.20.56 | In SM005 |
| 19100057 | BU (Assembly Shelf) | 00:50:51:FF:00:04 | 192.168.20.57 | Assigned to SM004 not installed. Reassigned to SM006. |
| 19100059 | BU (Assembly Shelf) | 00:50:51:FF:00:70 | 192.168.20.70 | Second special IPMC |
| 19100060 | BU (Assembly Shelf) | 00:50:51:FF:00:08 | -DHCP- | In SM#8 at CERN |
| 19100062 | BU (Assembly Shelf) | 00:50:51:FF:00:09 | 192.168.20.62 | Assigned to SM009 not installed |
| 19100063 | BU (Assembly Shelf) | 00:50:51:FF:00:0A | 192.168.20.63 | Assigned to SM010 not installed |
| 19100067 | BU (Assembly Shelf) | 00:50:51:FF:00:02 | 192.168.20.67 | Assigned to SM002 not installed. Final IPMC in SM002. |
| 19100069 | BU (Assembly Shelf) | 00:50:51:FF:00:07 | 192.168.20.69 | Final IPMC in SM007 |
| 19100070 | BU (Assembly Shelf) | 00:50:51:FF:00:70 | 192.168.20.70 | Special IPMC (1 of 2 at Cornell I believe -Felex) |
| 19100072 | 192.168.20.72 | Put in SM003 |
Switch
| ID | Location | History |
| 21 | BU (Assembly Shelf) | Final in SM009 |
| 22 | BU (Assembly Shelf) | SM001 |
| 23 | BU (Assembly Shelf) | |
| 24 | BU (Assembly Shelf) | Used for special IPMC testing. Final switch in SM 007 |
| 25 | BU (Assembly Shelf) | Final in SM006 |
| 26 | BU (Assembly Shelf) | Final in SM008 |
| 27 | BU (Assembly Shelf) | Assigned to SM004 not installed |
| 28 | BU (Assembly Shelf) | Final in SM010 |
| 29 | BU (Assembly Shelf) | Final in SM002 |
| 30 | BU (Assembly Shelf) | |
| 31 | BU | SM-003 |
| 32 | BU (Assembly Shelf) | |
| 35 | BU (Assembly Shelf) | |
| 36 | BU (Assembly Shelf) | |
| 37 | BU (Assembly Shelf) | |
| 38 | BU (Assembly Shelf) | |
| 39 | BU (Assembly Shelf) | |
| 40 | BU (Assembly Shelf) | |
| 41 | BU (Assembly Shelf) | |
| 42 | BU (Assembly Shelf) |
FP Board
RevA
| BU ID | FAB ID | Location | History |
| 0001 | BU (Assembly Shelf) | ||
| 0002 | BU (Assembly Shelf) | ||
| 0003 | BU (Assembly Shelf) | ||
| 0004 | BU (Assembly Shelf) | ||
| 0005 | BU | SM-001 | |
| 0006 | BU (Assembly Shelf) |
Rev B
| BU ID | FAB ID | Location | History |
| 0010 | BU | Using to test all blades up to after zynq boot. Previously zynq booted at varying rate. Final in SM009. | |
| 0011 | BU | LEDs did not light, replaced R1, fixed. Final in SM007. | |
| 0012 | BU | SD Card Slot replaced. Weird behavior while testing SM007 after Zynq installed. | |
| 0013 | BU | Blade 005 | |
| 0014 | BU | SD Card pins shorted | |
| 0015 | BU |
Rev C
| BU ID | FAB ID | Location | History |
| 20 | SM-10 | ||
| - | 0001 | Button seems to stick | |
| - | 0002 | ||
| - | 0003 | SM-02 | |
| - | 0004 | ||
| - | 0005 | ||
| - | 0006 | SM-08 |
Enclustra
| ID | Type | location | eth0 mac | eth1 mac | history |
| SN134522 | 35 | BU (table) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | was in eval board (in SM001) |
| SN141687 | 35 | BU (Assembly Shelf) | 00-50-51-FF-20-07 | 00-50-51-FF-10-07 | Final in SM007 |
| SN141688 | 35 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | |
| SN144976 | 35 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | Final in SM009 |
| SN144977 | 35 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | Final in SM010 |
| SN144978 | 35 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | Test Zynq (6, 8, 2). Assigned to SM006 |
| SN144979 | 35 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | Assigned to SM004 |
| SN144981 | 35 | BU (table) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | was in SM-001, dead in eval board.... |
| SN141805 | 45 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | Final in SM002 |
| SN144930 | 45 | BU (Assembly Shelf) | 00-50-51-FF-2X-XX | 00-50-51-FF-1X-XX | in SM-001 |
MAC/IP address assignment
We use the lower bits to enumerate the Service Modules. The 2 upper bits would describe its IPMC and Zynq ports. This way, looking at the address, we know exactly which board we are talking about.
Another slight change would be to have the other 2 bits of the upper reserved digit as zeros, so it is easier to identify where our address region starts.
Instead of 4k, we would use 16K, like the following:
00-50-51-FF-00-00 to 00-50-51-FF-3F-FF
Or, in more detailes:
00-50-51-FF-YX-XX
XXX: Number of the Service module Y: IPMC or Zynq ports (00, 01, 10, 11)
For example:
IPMC of the SM1: 00-50-51-FF-00-01 ZYNQ port facing Eth sw of the SM1: 00-50-51-FF-10-01
IPMC of the SM2: 00-50-51-FF-00-02 ZYNQ port facing Eth sw of the SM2: 00-50-51-FF-10-02
IPMC of the SM15: 00-50-51-FF-00-0F ZYNQ port facing Eth sw of the SM15: 00-50-51-FF-10-0F
