wiki:Apollo Inventory

Version 59 (modified by dgastler, 2 months ago) (diff)

--

Service Module

Rev A

ID Cirex Location Notes ECOs
001 98716 BU (table) Hard-wired 12V on, misc on, zynq bank IO on. Pulldown on zynq_en. 1k pulldown on U15 pin 1. Jumper on switch en to 3.3V 1, 2
002 98724 BU (Assembly Shelf) for show. Test paused after zynq booted successfully. 1, 2
003 BU (table) 1k pulldown on U15. switch fix 1, 2
004 98719 BU (Assembly Shelf) Resistor between R95 and R92 came off before step "put in zynq." LEDs lit up incorrectly. Stopped testing. Trial 2: Numerous LEDs lit up incorrectly at the same step (6: put in zynq). Stopped again. 1, 2
005 98720 BU (in Shelf) LEDs hot-wired permanently on 1, 2
006 98721 BU (Assembly Shelf) Test paused after zynq booted successfully. 1, 2
007 98723 Amhert Missing LED after all ECOs completed. Resoldered new LED. Test completed. 1, 2
008 98717 BU (Assembly Shelf) Missing LED after all ECOs completed. Resoldered new LED. Test paused after zynq booted successfully. 1, 2
009 98725 Cornell? Test paused after zynq booted successfully. Test completed. 1, 2
010 98718 BU (Assembly Shelf) Test paused after zynq booted successfully. 1, 219100056

ECO_1: Connect J5 pin-14 to 3V3_STBY through any lower 3 pins of J5 (p 2,4,6).

ECO_2: Add a 1k-Ohm resistor between the pad of R40 to GND pin of J12.

IPMC

Default IP is 192.168.1.34

CERN

ID Location MAC IP History
19100056 BU (Assembly Shelf) 00:50:51:FF:00:05 192.168.20.56 In SM005
19100057 BU (Assembly Shelf) 00:50:51:FF:00:04 192.168.20.57 Assigned to SM004 not installed
19100059 BU (Assembly Shelf) 00:50:51:FF:00:70 192.168.20.70 Second special IPMC
19100060 BU (Assembly Shelf) 00:50:51:FF:00:08 192.168.20.60 Assigned to SM008 not installed
19100062 BU (Assembly Shelf) 00:50:51:FF:00:09 192.168.20.62 Assigned to SM009 not installed
19100063 BU (Assembly Shelf) 00:50:51:FF:00:0A 192.168.20.63 Assigned to SM010 not installed
19100067 BU (Assembly Shelf) 00:50:51:FF:00:02 192.168.20.67 Assigned to SM002 not installed
19100069 BU (Assembly Shelf) 00:50:51:FF:00:07 192.168.20.69 Final IPMC in SM007
19100070 BU (Assembly Shelf) 00:50:51:FF:00:70 192.168.20.70 Special IPMC
19100072 192.168.20.72 Put in SM003

Switch

ID Location History
21 BU (Assembly Shelf) Final in SM009
22 BU (Assembly Shelf)
23 BU (Assembly Shelf)
24 BU (Assembly Shelf) Used for special IPMC testing. Final switch in SM 007
25 BU (Assembly Shelf) Final in SM006
26 BU (Assembly Shelf) Final in SM008
27 BU (Assembly Shelf) Assigned to SM004 not installed
28 BU (Assembly Shelf) Final in SM010
29 BU (Assembly Shelf) Final in SM002
30 BU (Assembly Shelf)
31 BU SM-003
32 BU (Assembly Shelf)
35 BU (Assembly Shelf)
36 BU (Assembly Shelf)
37 BU (Assembly Shelf)
38 BU (Assembly Shelf)
39 BU (Assembly Shelf)
40 BU (Assembly Shelf)
41 BU (Assembly Shelf)
42 BU (Assembly Shelf)

FP Board

RevA

BU ID FAB ID Location History
0001 BU (Assembly Shelf)
0002 BU (Assembly Shelf)
0003 BU (Assembly Shelf)
0004 BU (Assembly Shelf)
0005 BU SM-001
0006 BU (Assembly Shelf)

Rev B

BU ID FAB ID Location History
0010 BU Using to test all blades up to after zynq boot. Previously zynq booted at varying rate. Final in SM009.
0011 BU LEDs did not light, replaced R1, fixed. Final in SM007.
0012 BU SD Card Slot replaced. Weird behavior while testing SM007 after Zynq installed.
0013 BU Blade 005
0014 BU SD Card pins shorted
0015 BU

Enclustra

ID Type location eth0 mac eth1 mac history
SN134522 35 BU (table) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX was in eval board (in SM001)
SN141687 35 BU (Assembly Shelf) 00-50-51-FF-20-07 00-50-51-FF-10-07 Final in SM007
SN141688 35 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX
SN144976 35 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX Final in SM009
SN144977 35 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX Final in SM010
SN144978 35 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX Test Zynq (6, 8, 2)
SN144979 35 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX Assigned to SM004
SN144981 35 BU (table) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX was in SM-001, dead in eval board....
SN141805 45 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX
SN144930 45 BU (Assembly Shelf) 00-50-51-FF-2X-XX 00-50-51-FF-1X-XX in SM-001

MAC/IP address assignment

We use the lower bits to enumerate the Service Modules. The 2 upper bits would describe its IPMC and Zynq ports. This way, looking at the address, we know exactly which board we are talking about.

Another slight change would be to have the other 2 bits of the upper reserved digit as zeros, so it is easier to identify where our address region starts.

Instead of 4k, we would use 16K, like the following:

00-50-51-FF-00-00 to 00-50-51-FF-3F-FF

Or, in more detailes:

00-50-51-FF-YX-XX

XXX: Number of the Service module Y: IPMC or Zynq ports (00, 01, 10, 11)

For example:

IPMC of the SM1: 00-50-51-FF-00-01 ZYNQ port facing Eth sw of the SM1: 00-50-51-FF-10-01

IPMC of the SM2: 00-50-51-FF-00-02 ZYNQ port facing Eth sw of the SM2: 00-50-51-FF-10-02

IPMC of the SM15: 00-50-51-FF-00-0F ZYNQ port facing Eth sw of the SM15: 00-50-51-FF-10-0F