Service Module
Rev A
ID | Cirex | Location | Notes | ECOs
|
001 | 98716 | BU (table) | Hard-wired 12V on, misc on, zynq bank IO on. Pulldown on zynq_en. 1k pulldown on U15 pin 1. Jumper on switch en to 3.3V | 1, 2
|
002 | 98724 | BU (Assembly Shelf) | for show | 1, 2
|
003 | | UMass Amherst | 1k pulldown on U15. switch fix | 1, 2
|
004 | 98719 | BU (Assembly Shelf) | | 1, 2
|
005 | 98720 | BU (table) | LEDs hot-wired permanently on | 1, 2
|
006 | 98721 | BU (Assembly Shelf) | | 1, 2
|
007 | 98723 | BU (Assembly Shelf) | | 1, 2
|
008 | 98717 | BU (Assembly Shelf) | | 1, 2
|
009 | 98725 | BU (Assembly Shelf) | | 1, 2
|
010 | 98718 | BU (Assembly Shelf) | | 1, 2 | 19100056
|
ECO_1: Connect J5 pin-14 to 3V3_STBY through any lower 3 pins of J5 (p 2,4,6).
ECO_2: Add a 1k-Ohm resistor between the pad of R40 to GND pin of J12.
IPMC
CERN
ID | Location | MAC | IP | History
|
19100056 | BU (Assembly Shelf) | | 192.168.20.56 |
|
19100057 | BU (Assembly Shelf) | | 192.168.20.57 |
|
19100059 | BU (Assembly Shelf) | | 192.168.20.59 |
|
19100060 | BU (Assembly Shelf) | | 192.168.20.60 |
|
19100062 | BU (Assembly Shelf) | | 192.168.20.62 |
|
19100063 | BU (Assembly Shelf) | | 192.168.20.63 |
|
19100067 | BU (Assembly Shelf) | | 192.168.20.67 |
|
19100069 | BU (Assembly Shelf) | | 192.168.20.69 |
|
19100070 | BU (Assembly Shelf) | | 192.168.20.70 |
|
19100072 | | | 192.168.20.72 | Put in SM003
|
Switch
ID | Location | History
|
21 | BU (Assembly Shelf) |
|
22 | BU (Assembly Shelf) |
|
23 | BU (Assembly Shelf) |
|
24 | BU (Assembly Shelf) |
|
25 | BU (Assembly Shelf) |
|
26 | BU (Assembly Shelf) |
|
27 | BU (Assembly Shelf) |
|
28 | BU (Assembly Shelf) |
|
29 | BU (Assembly Shelf) |
|
30 | BU (Assembly Shelf) |
|
31 | BU | SM-003
|
32 | BU (Assembly Shelf) |
|
35 | BU (Assembly Shelf) |
|
36 | BU (Assembly Shelf) |
|
37 | BU (Assembly Shelf) |
|
38 | BU (Assembly Shelf) |
|
39 | BU (Assembly Shelf) |
|
40 | BU (Assembly Shelf) |
|
41 | BU (Assembly Shelf) |
|
42 | BU (Assembly Shelf) |
|
FP Board
BU ID | FAB ID | Location | History
|
| 0001 | BU (Assembly Shelf) |
|
| 0002 | BU (Assembly Shelf) |
|
| 0003 | BU (Assembly Shelf) |
|
| 0004 | BU (Assembly Shelf) |
|
| 0005 | BU | SM-001
|
| 0006 | BU (Assembly Shelf) |
|
FP Board Rev B
BU ID | FAB ID | Location | History
|
| 0010 | BU |
|
| 0011 | BU | LEDs do not light
|
| 0012 | BU | SD Card Slot replaced
|
| 0013 | BU | Blade 005
|
| 0014 | BU | SD Card pins shorted
|
| 0015 | BU |
|
Enclustra
ID | Type | location | history
|
SN134522 | 35 | BU (table) | was in eval board
|
SN141687 | 35 | BU (Assembly Shelf) |
|
SN141688 | 35 | BU (Assembly Shelf) |
|
SN144976 | 35 | BU (Assembly Shelf) |
|
SN144977 | 35 | BU (Assembly Shelf) |
|
SN144978 | 35 | BU (Assembly Shelf) |
|
SN144979 | 35 | BU (Assembly Shelf) |
|
SN144981 | 35 | BU (table) | was in SM-001, dead in eval board....
|
SN141805 | 45 | BU (Assembly Shelf) |
|
SN144930 | 45 | BU (Assembly Shelf) |
|
MAC/IP address assignment
For now, we use the IPMC serial number to set the MAC and IP addresses.
IP address is 192.168.20.xx where xx is the last part of the IPMC serial number.
MAC address is 00-50-51-ff-f0-xx
where xx is the IPMC serial number.
This is subject to change!